Concrete Drainage Channels

Concrete Drainage Channels: A Practical Guide for Irish Sites

Concrete Drainage Channels: A Practical Guide for Irish Sites

A concrete drainage channel is a shaped run of precast, slip-formed or cast in situ concrete that collects surface water and carries it to an outfall, gully or soakaway. On an Irish site, getting one right comes down to four decisions: the load class, the hydraulic design, how the channel is bedded and haunched, and who keeps it clear afterwards. This guide takes you through each, and explains where ready mix, mini mix and pumping fit into the job.

  • Choose the channel and grating for the heaviest wheel load it will ever see, because the weaker of the two parts sets the load class.
  • Size the channel and place the outlets from a hydraulic calculation, not by eye. Flat ground needs more frequent outlets.
  • Lay from the outlet upwards on fresh bedding concrete, then haunch both sides to the strength the load class requires.
  • Keep the grating and channel clear of silt, leaves and debris, and check them after heavy rain.
  • Where the trench is awkward to reach with a wheelbarrow or chute, a pump or mini mix delivery saves time and protects the line you have just set.

What a concrete drainage channel does

Surface water has to go somewhere. Left alone, it stands on paving, undermines edges and finds its way towards doors and foundations. A channel intercepts that water across the width of a surface, or along its edge, and moves it on in a controlled way.

Ireland’s Guidelines for Road Drainage describe road drainage as removing and controlling surface and subsurface water, including intercepting and diverting water from the carriageway. The same document notes that drainage needs enough capacity and longitudinal slope to move that water. Those two ideas, capacity and fall, apply just as well to a yard, a driveway or a loading bay.

On roads, the guidelines describe concrete channels as rounded or triangular sections, slip-formed, cast in situ or precast, set at the pavement edge and flush with the surface. Transport Infrastructure Ireland says much the same in its Drainage Systems for National Roads document: surface-water channels are normally triangular or trapezoidal concrete sections, usually slip-formed.

Triangular concrete channel beside an Irish road

On private and commercial sites you will more often meet the other family: linear channels with a grating on top, which sit across a drive, a threshold, a yard or a car park. Both families are made from concrete, and both rely on the same good groundwork.

Where concrete channels are used

Concrete channels turn up wherever there is a lot of paved area and a need for something robust. Typical settings include:

  • Domestic driveways and garage thresholds, where a narrow channel stops water running towards the house.
  • Farm yards and agricultural hardstanding, where wheel loads are heavy and cleaning is regular.
  • Car parks, loading bays and industrial yards.
  • Public roads and national road schemes, where edge channels are standard.

TII publishes Standard Construction Details for Series 500 drainage, which include specifications for concrete surface water channel blocks in types A to F. If you are working on or near a public road, these are the details the engineer is likely to refer to, so ask early which one applies.

Precast, slip-formed or cast in situ?

There are three ways to get concrete into the ground as a channel, and each suits a different job.

Method Best suited to Things to weigh
Precast units Driveways, yards, car parks, most building sites Quick to lay, consistent profile, needs bedding and haunching concrete around it
Slip-formed Long, continuous runs along kerbs and road edges Needs a slip-form machine and a steady supply of concrete
Cast in situ Short runs, special shapes, tie-ins to existing work Needs formwork and skilled finishing, so it is slower

Precast is the usual choice for private and small commercial work, and even then concrete does a lot of the work: the bedding under the units and the haunching around them are both poured on site.

Choosing the load class

The most common and most expensive mistake is fitting a channel that cannot take the traffic. Load classes under BS EN 1433 describe the tested load-bearing strength of channel products. According to this load class classification sheet, they are not static-weight ratings, and they run as follows:

Class Typical use
A15 Pedestrians and cycleways
B125 Pedestrian precincts and light vehicles
C250 Parking areas and slow-moving light commercial vehicles
D400 Public highways and parking for all vehicle types
E600 Industrial areas, heavy wheel loads and forklifts
F900 Aircraft runways and very heavy industrial and military installations

A few practical points follow from this:

  • Think about the worst day, not the average one. A domestic drive is fine at a lower class until a delivery lorry or a concrete truck backs onto it. If a heavy vehicle will ever cross the channel, specify for it.
  • Channel body and grating work together. As the Pavingexpert guide to linear drains explains, the lower-rated component dictates the class of the whole system. A strong grating in a weak body, or the reverse, gives you the weaker rating.
  • Match the grating to the use. Gratings come in materials such as galvanised steel, polypropylene, ductile iron and stainless steel. Heavier traffic and wet, dirty environments push you towards ductile iron or stainless steel.

The concrete around the channel is part of the answer too. The haunching is what carries the load into the ground, so the class of the unit is only as good as the concrete placed beside it.

Hydraulic design and site factors

Before a single trench is dug, confirm the load class, the hydraulic design, the finished surface, the outlet location and the manufacturer’s instructions. Hydraulic design is what fixes the channel size, the run length and where the outlets go.

You do not need to be an engineer to understand what that means:

  1. Catchment. How much paved or roofed area drains to this channel? The National Transport Authority’s typical construction detail for linear drainage says channel width should be determined by the overall catchment area and outfalls, and requires linear drainage to comply with BS EN 1433.
  2. Fall. The ground must slope towards the channel and the channel must run to the outlet. Kildare County Council’s concrete kerb inlet detail specifies a 1:40 fall of the carriageway toward the channel, and shows the channel discharging to a sustainable drainage feature such as a rain garden, basin or swale.
  3. Outlets. The road drainage guidelines explain that channel outlets can be widely spaced, but flat longitudinal gradients may need fairly frequent discharge points so that the channel can stay small.
  4. Where the water ends up. Foul and surface water rules differ. Technical Guidance Document H covers drainage and wastewater disposal in the Building Regulations, and the 2016 edition amends the 2010 edition. Your designer or local authority will tell you what applies to your connection.

For anything beyond a small domestic run, ask a drainage designer or engineer to confirm the channel size and outlet positions. It costs far less than lifting a finished slab.

Installing a concrete drainage channel

Installation guidance from manufacturers follows the same logic. Here is the sequence in plain terms. Always follow the instructions supplied with the product you are using, because details such as joint sealing and finished levels vary between systems.

1. Set out and excavate

Mark the line and the outlet. Dig a trench wide enough for the bedding and the side concrete, and deep enough for the unit, the bedding beneath it and the surfacing above. The excavation and foundation support must suit the drainage system and its load class. Heavier classes need more concrete around the channel.

2. Lay from the outlet upwards

Fix a string line to guide level and direction. Start at the outlet or lowest point and work uphill, placing each unit in its marked flow direction on fresh bedding concrete, as set out in Marshalls’ linear drainage installation guidelines. Seal adjacent joints where the system calls for it.

Fresh bedding matters. Concrete that has started to go off will not bond or bed the unit properly, which is why delivery timing is so important on this job (more on that below).

3. Protect the channel and haunch it

Channels are light and open-topped, so protect them during concreting: keep concrete out of the channel and fill or cover it as the manufacturer advises. Then place concrete up both sides to the thickness the load class and the manufacturer require. Work it in so there are no voids under the haunch.

4. Get the finished level right

The adjoining surface and the top of the channel need to meet at a carefully chosen relationship, usually a few millimetres, so that water runs in and wheels do not hammer the edge. The exact figure depends on the system, so follow the product’s own instruction sheet and check it before the surface goes down.

5. Allow for movement

Leaving out expansion joints, choosing the wrong load class, poor outlet planning and wrong surface levels are the most common installation errors that cut performance. A good concrete finisher will plan joints before the first load arrives.

Getting the concrete to the trench

This is the part of the job many guides skip, and it is where site problems start. A drainage channel trench is long, narrow and often at the back of a house, along a boundary, or beside a building. The concrete has to get there fresh and in the right quantity.

There are three practical ways:

  • Ready mix straight from the truck. Ready mix concrete works well when the truck can chute directly into or close to the trench.
  • Mini mix for tight sites. For small quantities or narrow access, mini mix concrete avoids ordering more than you need and fits where a full-size truck cannot.
  • Pumping for long or awkward runs. If the trench is a long way from where the truck can stand, concrete pumping places the concrete exactly where it is wanted, without a chain of wheelbarrows trampling the line you have set. Concrete line pumping is particularly useful when access is through a house, along a narrow passage or across a garden.

Wheelbarrowing concrete along a trench is slow, and the first loads start to stiffen before the last are placed. A pump keeps the pour continuous, which gives you a more consistent haunch and fewer cold joints.

Our perspective

Our perspective

We have supplied and pumped concrete across Leinster for over 30 years, and drainage channel work has taught us a few things. The first is that the channel itself is rarely the problem. The trouble is almost always timing and access: a trench that is ready, a unit that is set, and then concrete that arrives late or cannot get close enough.

So we ask the same questions on every call. How far is the trench from where the truck can stand? How much concrete will the bedding and both haunches take? Is there a gate, a passage or a house in the way? From those answers we can usually say whether ready mix, mini mix or a pump is the sensible choice, and sometimes that is the cheaper, simpler option rather than the bigger one.

Our advice to builders and homeowners alike is to work out the concrete volume with your installer before the trench is opened, book the delivery for when the channel is set and checked, and pour the haunching in one continuous go. Doing it that way, at the right time, is how you deliver a solid foundation for the paving that goes on top.

CastleGS Concrete Pumping, Maynooth

Need concrete for a drainage run?

You can see everything we offer on our concrete pumping services page, or learn more about our company and our family-run approach to personal service.

Cleaning and maintaining channels

One reason concrete channels are popular is that they are easy to look after. The Irish road drainage guidelines identify concrete channels as easy to maintain, and, for channel drains generally, they stress providing safe and suitable maintenance access and choosing gratings with blockage risk in mind.

A simple routine is enough for most sites:

Channel maintenance checklist

Farm yards, car parks and leafy driveways need cleaning more often than a clean patio. Put it in the diary, rather than waiting for the first puddle.

Common mistakes to avoid

  • Underspecifying the load class because the site “will only see cars”. Concrete deliveries, skips and bin lorries all count.
  • Skipping the hydraulic check on larger paved areas, so the channel overflows in the first storm.
  • Poor outlet planning, with the channel running to nowhere or to a point higher than the channel itself.
  • Finishing the surface too high so that water bridges over the top instead of entering.
  • Starting the pour before the channel is secured, so units float or move as concrete goes in.
  • Ordering concrete too early or too late. Fresh bedding is the goal, so coordinate delivery with the laying crew.

FAQ

What load class do I need for a domestic driveway?

For a driveway used by cars, a B125 or C250 class is usually considered. If lorries, delivery vehicles or concrete trucks will cross the channel, go higher. The class is set by the lower-rated of the channel and the grating, so check both with your supplier.

Do I need concrete around a precast channel?

Yes, in most cases. Manufacturers’ installation guidance calls for the channel to be laid on bedding concrete and then haunched at the sides, with the strength and thickness depending on the load class. Follow the instructions supplied with your product.

How far apart should outlets be?

That depends on the catchment area, the gradient and the channel size. Irish road drainage guidance says outlets can be widely spaced on good falls, while flat gradients may need more frequent discharge points. A hydraulic calculation will give you the answer for your site.

How do I get concrete to a trench behind a house?

If a truck cannot get close, use mini mix for small volumes or a line pump for longer or more awkward runs. A pump delivers concrete through a hose to the exact point where it is needed, which also keeps the trench and the set channel undisturbed.

How often should I clean a drainage channel?

Check the grating and channel regularly and after heavy rain, and clear any silt, leaves or debris. Sites with more leaf fall, mud or traffic, such as farm yards, need more frequent attention.

Written by GS Concrete Pumping

Supplying and pumping concrete across Leinster since 1993, from house foundations and extensions to commercial and civil projects. Questions about your pour? Call 01 963 6055.

Book the right pump, first time

Over 30 years pumping concrete for house foundations, commercial builds, floors, farms and civil works across Leinster.